UPS and Stabilizer Repair in Baku
UPS and voltage stabilizer repair: charging circuit, inverter stage and control board, restored at component level.
Order
Send the make and model and describe the fault briefly. A video helps most — film the fault. Clear photos of the board help too.
Repair of UPS units, voltage stabilizers and inverters. Component-level board repair: control board, inverter stage, charging circuit, bypass relay and battery management. APC, Eaton, Powercom, Ippon.
How we work
Not every device can be repaired
Sometimes restoration is not possible: the chip is discontinued and no spare can be sourced, no donor board is available, the board is severely damaged by fire or liquid, or earlier repair attempts have left it beyond recovery. In such cases we explain the situation plainly and, where possible, suggest an alternative.
UPS units and stabilizers usually fail because of electronics, not the battery. "I replaced the battery and it still does not work" is the sentence we hear most — the real fault is normally in the charging circuit, the inverter stage or the control board.
On line-interactive units the relay and AVR section fail most often: the device switches to battery while the mains is fine, or the relay clicks continuously. On online units the problem is usually in the rectifier and inverter cascade.
In stabilizers the typical faults are burnt relays, a drifted measuring circuit and a locked-up control microcontroller. In many cases the transformer is intact and only the board needs restoring.
For industrial and server-room units on-site diagnostics can be arranged — moving such equipment is both difficult and risky.
If you are looking for an electronics or board-level technician — this work is done at component level: the fault is fixed by replacing the specific part, not the whole unit.
Devices we repair
Common faults we repair
- Mains present but UPS runs from battery
- New battery still drains quickly
- Continuous beeping, will not take load
- Error code on display, stuck in bypass
- Not charging, battery voltage does not rise
- No output voltage
- Stabilizer does not regulate voltage
- Relay clicks constantly, output jumps
- Transformer overheats, burning smell
- Trips the breaker on start-up
- Fan not running, unit overheats
- Dead after a mains surge
Typical causes of failure
- Prolonged under- or over-voltage in the mains
- Charging circuit overloaded by a battery left unreplaced for too long
- High inrush loads (motors, compressors) connected to the UPS
- Stopped fan and an overheating power stage
- Moisture and dust, especially in basements and storage rooms
- Dried electrolytic capacitors shifting the output voltage
- Lightning and mains surges
Brands and platforms we work with
How the repair works
- 01
Enquiry and first contact
Tell us about the fault on WhatsApp or Telegram. We review what you send and let you know whether the device fits the work we take on.
- 02
Acceptance and diagnostics
If we can take the device on, we confirm it in advance — do not ship it before you have our confirmation. Once it reaches the lab, diagnostics are completed within 48 hours (two working days).
- 03
Estimate and approval
You receive a report covering the cause of the fault, the estimated cost, spare-part availability and the timeline. Work begins only after you approve it.
- 04
Testing and handover
After the repair the device runs a minimum 24-hour load test. Once it proves stable in normal operation, we report the result and hand it over.
Diagnostics and pricing
Diagnostics is paid work — 10–50 AZN depending on the complexity of the board. If you have us carry out the repair, that amount is deducted from the final price. An exact repair price is given only after diagnostics and is agreed with you before any work starts.
More about the diagnostic feeFrequently asked questions
Other repair areas
Request a repair
Message us on WhatsApp or Telegram with the BRAND and MODEL of the device and describe the fault in as much detail as you can. A VIDEO helps most: record the fault and explain in your own words what happens. Also send clear photos of the device and, if accessible, of the circuit board from several angles. The more detail you provide, the faster and more accurate our answer.