Cosmetology Equipment Repair in Baku
Cosmetology equipment electronics repair in Baku — circuit board repair, power supply and cooling system restoration for laser hair removal devices, cavitation, RF lifting, cryolipolysis, hydrafacial units and salon combines.
Order
Send the make and model and describe the fault briefly. A video helps most — film the fault. Clear photos of the board help too.
Electronics repair for laser hair removal devices (diode, alexandrite), cavitation, RF lifting, cryolipolysis, hydrafacial units and cosmetic combines. Power supply, control board, cooling circuit and applicator handpiece restoration.
How we work
Not every device can be repaired
Sometimes restoration is not possible: the chip is discontinued and no spare can be sourced, no donor board is available, the board is severely damaged by fire or liquid, or earlier repair attempts have left it beyond recovery. In such cases we explain the situation plainly and, where possible, suggest an alternative.
In beauty salon equipment the most common fault is not in the device itself but in its power and cooling section: the laser hair removal unit fires no pulse, the cryolipolysis unit will not reach temperature, the cavitation handpiece goes silent. The great majority of these are restored at component level — there is no need to buy a whole module or handpiece.
On diode and alexandrite lasers we check the power supply, the capacitor bank, the control board and the applicator cable — the work is circuit board repair, not wholesale assembly replacement. On RF lifting and cavitation devices the generator circuit and handpiece matching are the weak points; on hydrafacial units it is the vacuum pump and valve assembly.
For a salon, downtime is a direct loss, so we diagnose quickly and tell you early whether a repair is feasible. If the device cannot be restored, only the diagnostic fee is charged.
Devices we repair
Dedicated pages in this area
Common faults we repair
- The laser hair removal device fires no pulse, the handpiece does not light
- Laser output has weakened, sessions give no result
- The cavitation handpiece is dead
- The RF lifting unit's electrode does not heat or throws an error
- The cryolipolysis unit will not reach temperature
- The hydrafacial device holds no vacuum, the pump is dead
- The cosmetic combine will not start, the screen stays dark
- The device runs briefly then goes into protection
- The cooling system (chiller) leaks or the fan has stopped
- The touch screen is unresponsive, the menu freezes
- Foot pedal and connector faults
- The autoclave does not complete its sterilisation cycle
Typical causes of failure
- Power supply burnt by a mains voltage surge
- Overheating after the coolant ran low or the chiller stopped
- A break in the laser applicator cable, usually where it bends most
- An aged capacitor bank, dropping the pulse energy
- Failure of the piezo element in ultrasonic and RF handpieces
- Valve wear and air leaks in the vacuum pump
- Loss of contact in the touch panel ribbon
- Circuit damage from an earlier unskilled repair
Brands and platforms we work with
How the repair works
- 01
Enquiry and first contact
Tell us about the fault on WhatsApp or Telegram. We review what you send and let you know whether the device fits the work we take on.
- 02
Acceptance and diagnostics
If we can take the device on, we confirm it in advance — do not ship it before you have our confirmation. Once it reaches the lab, diagnostics are completed within 48 hours (two working days).
- 03
Estimate and approval
You receive a report covering the cause of the fault, the estimated cost, spare-part availability and the timeline. Work begins only after you approve it.
- 04
Testing and handover
After the repair the device runs a minimum 24-hour load test. Once it proves stable in normal operation, we report the result and hand it over.
Diagnostics and pricing
Diagnostics is paid work — 10–50 AZN depending on the complexity of the board. If you have us carry out the repair, that amount is deducted from the final price. An exact repair price is given only after diagnostics and is agreed with you before any work starts.
More about the diagnostic feeFrequently asked questions
Other repair areas
Request a repair
Message us on WhatsApp or Telegram with the BRAND and MODEL of the device and describe the fault in as much detail as you can. A VIDEO helps most: record the fault and explain in your own words what happens. Also send clear photos of the device and, if accessible, of the circuit board from several angles. The more detail you provide, the faster and more accurate our answer.